Roller Door Prices NZ: Compare Supply, Install & Automation

Shopping for a roller garage door? In NZ, a roller door is a corrugated steel or aluminium curtain that coils above the opening, freeing ceiling space and suiting tight driveways. “Roller door prices” means what you’ll pay for the door, any motor, and optionally installation and freight. The total depends on size, material and finish, wind rating, and whether you choose manual or automated.

This guide gives you NZ price ranges (incl. GST) you can budget against, comparing supply-only and supplied-and-installed for single and double doors, plus opener options. You’ll see how materials (Coloursteel, Zincalume, aluminium), sizes and wind zones change the quote; how to measure correctly; DIY vs pro install costs; key add‑ons; delivery timeframes; and smart ways to save without cutting quality. Ready to compare? First up, the factors that move price.

What affects roller door prices in New Zealand

Roller door prices in NZ move with a handful of predictable factors. The big levers are the door’s size and wind rating, the material and finish you choose, and whether you add automation or professional installation. Site constraints and freight also matter, so a quick measure and postcode check can sharpen any quote.

• Size (width/height): more material, heavier gauge.
• Material/finish: Coloursteel vs Zincalume (+10–15%); aluminium (+20–30%).
• Wind zone/coastal: wind‑locking, thicker slats, spec upgrades.
• Automation: opener $400–$900; accessories extra.
• Installation: pro fit $350–$650; alterations add.
• Site constraints: headroom/side room can change hardware.
• Freight/region: South Island lead time/freight premiums.

At-a-glance price ranges (NZD, incl. GST)

For quick budgeting, here are realistic ballparks for common domestic sizes. These roller door prices NZ buyers see most often cover NZ-made steel doors; installation assumes a standard site. Add automation separately. Quotes shift with size, wind zone and access.

• Manual installed: typical hand-operated domestic doors land around $1,800–$3,000.
• Low-budget supply: some suppliers list smaller single doors from about $700–$1,100 supply-only; check spec and wind rating before you buy.

Single vs double roller doors: costs and best fit

A single domestic roller (around 2.4 m × 2.1 m) typically sits at $1,200–$2,000 supply-only or $1,550–$2,650 supplied and installed. A double width (around 4.8 m × 2.4 m) runs $2,000–$3,300 supply-only or $2,800–$4,300 installed. Add $400–$900 for automation. Doubles approach the domestic width limit, and in medium–high wind zones may need heavier spec or wind-lock guides, pushing costs up.

• Choose a single: one‑car garages, sheds, very high wind sites, or when you want the lowest price and simplest spec.
• Choose a double: two‑car garages needing full-width access; plan for a motor and confirm wind rating before you buy.

Supply-only vs supplied and installed

Supply-only suits DIYers; you’ll save roughly $350–$650 per single door versus paying a tech, but you take on measuring, lifting and spring tensioning. Supplied-and-installed suits time-poor buyers or anyone needing insurance compliance; install pricing typically runs $350–$650 (some quote $350–$500) on top of the door, covering standard timber framing, disposal of the old door and basic set‑up. Pros bring calibrated tension bars and laser levels, and you get installation warranty and a compliance certificate. Region or access constraints, wind upgrades and alterations can add.

Manual vs automated: opener types and pricing

If you’re comparing roller door prices in NZ, the biggest lifestyle upgrade is automation. Manual spring‑balanced doors are the lowest upfront cost and suit sheds or sites without power. Add a motor and you gain push‑button convenience, better security and smoother travel; domestic roller openers typically deliver 600–1000 N lift and bolt straight to the drum.

• Opener cost: most domestic units land at $400–$900 (some dealer packages quote $600–$750).
• Bundle and save: fitting a motor with a new door can save up to ~$450 versus retrofitting later.
• Core features: soft start/stop, auto‑close timer, LED courtesy light, quiet gear drive.
• Smart add‑ons: extra remotes $40–$80; keypad $95–$145; Wi‑Fi hub $140–$250; battery back‑up $120–$180.
• Compliance: safety beams and auto‑reverse are required under AS/NZS 4505 when you automate.

Domestic vs semi-industrial and commercial options

Domestic roller doors suit homes and sheds with standard daily use. Step up to semi‑industrial or commercial when you need wider spans, higher cycle counts or stronger wind performance. Expect heavier‑gauge slats, wind‑lock guides, chain drive and safety brakes. For roller door prices NZ buyers can budget from about $2,500 supply for small shopfronts to $6,000+ (incl. GST), or roughly $4,000–$9,000 installed for larger warehouse openings, with specialist upgrades adding 10–20%.

Materials and finishes: Coloursteel, Zincalume and aluminium

Your curtain material sets durability, look and, importantly, roller door prices NZ homeowners pay. Steel is the mainstream choice; you’re balancing corrosion resistance, colour options and wind performance against budget. In coastal areas, finish and warranty conditions matter—washed regularly, painted steel holds up well, while aluminium shrugs off rust altogether.

• Coloursteel: painted galvanised steel, 24+ colours, coastal warranties; mid-range price.
• Zincalume: silvery alloy coat; typically 10–15% cheaper than Coloursteel; ideal if painting later.
• Aluminium: light, rust-proof, wider spans; can be anodised or powder-coated; usually 20–30% more than Coloursteel.

Sizes, headroom and wind zones: what changes the quote

Dimensions and site conditions push roller door prices up or down because they dictate the hardware and gauge required. As width and height climb, you shift into higher price brackets and heavier slats. Tight headroom can force different mounting choices, and higher wind zones need wind-rated components. Near the domestic width ceiling, even small site constraints can trigger spec upgrades.

• Size steps: each width/height step typically adds $50–$150; very wide doors (approaching 4.8 m) can be unsuitable in medium–high wind areas without upgrades.
• Headroom: allow at least 420 mm above the lintel for a domestic drum; less headroom complicates install and may add cost.
• Side room: budget 90 mm clear each side for guides; tight reveals can slow installation.
• Wind zone: Very High/Extra High sites often need thicker slats or wind‑lock guides, adding a premium to the quote.

How to measure for an accurate price

Correct measurements lock in the right spec and prevent remakes. NZ quotes for roller door prices rely on these figures, so use a steel tape and a helper—garages are rarely perfectly square. Work to the smallest dimension, and photograph obstructions to speed up quoting.

1. Width: measure top/middle/bottom; use the smallest.
2. Height: floor to lintel, both jambs; use the lowest.
3. Headroom: lintel underside to ceiling/obstruction; need ≥420 mm.
4. Side room: opening edge to wall; allow 90 mm each side.
5. Reveal depth: inside lintel face to back wall; aim 400 mm.

Installation options: DIY steps, pro costs and compliance

DIY is doable for capable buyers, but you’ll need two people to lift a 40–60 kg roll and around 4–6 hours. Spring tensioning is the risky part. A professional install typically adds $350–$650 for a single, usually covering removal of the old door, set‑up, an install warranty and compliance paperwork. Book a pro for headroom under 420 mm, skewed frames or Very High wind zones.

• Install flow: fix brackets, seat/level drum, feed curtain into guides, tension spring or fit opener, then test balance/auto‑reverse. Two people, basic power tools and a level required.
• Compliance: AS/NZS 4505 wind‑loading applies; automation requires safety beams and auto‑reverse. High wind/coastal sites may need wind‑locks and heavier slats.

Accessories and add-ons to budget for

On top of the door/motor, budget for add-ons that lift convenience, security and compliance. These extras can nudge roller door prices NZ-wide. Common picks: extra remotes ($40–$80), wireless keypad ($95–$145), Wi‑Fi/smart hub ($140–$250) and battery back‑up ($120–$180). Safety beams are required when you automate. Consider auto‑locks, emergency key release and bird‑proofing brushes for coastal or dusty sites.

Delivery, lead times and regional freight

Most NZ-made roller doors are custom-built; typical lead times are Windsor 7 working days to manufacture (ships the following Monday) and Garador 15 working days (ships Friday). South Island add 1–2 weeks. North Island delivery is free; South Island subsidised to Christchurch depot (pickup), with extra for door-to-door to Dunedin, Southland, Nelson. Carriers call to confirm the day; delivery windows are not very flexible.

Smart ways to save without cutting quality

You can trim spend without ending up with a flimsy door. Focus on spec that matches your site, bundle smart, and use low‑overhead supply channels. Small choices like finish and freight method can shift roller door prices NZ buyers pay by hundreds with zero sacrifice in performance.

• Pick Zincalume: typically 10–15% less than Coloursteel.
• Buy online direct: same NZ-made curtains, leaner margins.
• Bundle automation: save up to ~$450 vs retrofitting; kits often shave $100+.
• Stay standard size: avoid costly wind‑lock/heavy‑gauge upgrades unless needed.
• DIY the prep (or full DIY): save $350–$650 on install; get a pro to final‑tension if unsure.
• Order off‑peak: winter promos and softer freight rates help.
• Optimise freight: North Island delivery is free; South Island depot pick‑up reduces cost.
• Protect your warranty: regular washing in coastal zones avoids premature repaint/repair spend.

Where to buy in NZ: dealer, big-box or online direct

Where you buy sets price, speed and support. Match the channel to your budget and how hands-on you want to be.

• Dealers/showrooms: measure-and-quote, full install, demo doors; usually 10–20% dearer, often brand‑limited.
• Big‑box: ready-made sizes, fast pickup; few colours/options, install is DIY.
• Online direct: custom NZ‑made, lean margins, phone support; free North Island delivery, subsidised South Island depot pickup; ideal for supply‑only/DIY, with optional install.

Warranty, maintenance and lifespan expectations

With the right spec and basic care, a roller door should deliver 20+ years. Typical cover runs 5–10 years for the steel/aluminium curtain (perforation/cracking) and 2–5 years for motors/electronics. Finish warranties in coastal zones usually require quarterly washing. Keep your compliance paperwork and serial numbers for insurance and claims.

• Wash and inspect quarterly; use mild detergent, wax painted steel annually.
• Silicone-spray guides and bottom seal twice yearly; balance check: half-open should stay put.
• Call a pro for binding, heavy travel, noisy bearings or uneven roll; replace when slats crease or rust penetrates the coating.

Next steps

You now know what drives roller door prices in NZ: single vs double ranges, supply-only vs installed, opener costs, materials, wind zones, and how to measure. Next, grab accurate widths, heights and headroom, photograph any obstructions, decide manual or motor, and shortlist your finish (Zincalume to save, Coloursteel for colour, aluminium for coastal/wide spans).

Send those measurements for instant pricing on NZ‑made doors, with free North Island delivery and subsidised South Island depot pick‑up, optional installation, and typical manufacture lead times of 7–15 working days (SI add 1–2 weeks). Ready to lock in a number? Get a fast, obligation‑free quote at DoorsNZ.